Float Framing Artwork Tutorial for Prints, Drawings, and Artwork on Paper

Framing Tutorial 31

I’ve set a goal of framing a bunch of prints/drawings that I’ve purchased from artists over the last few years so we can enjoy having them on display.  I’ve put together this tutorial for you all so you can feel confident in framing work without damaging it or plunking down serious cash at the frame shop.  This method of framing hinges the artwork from the top and lets it hang freely in a deep set shadowbox frame.  It lets the deckle edge show, and is easy to make with minimal material costs.

 Framing Tutorial 01

Materials:

  • Frame: a shadowbox frame that is proportionate to your artwork – I recommend buying frames in person as you can better gauge their quality.
  • Mat Board – I use archival Rag Mat Board – I don’t have to worry about it leeching acid or damaging prints/drawings over time.   
  • Mat Cutter (get one if you’re an artist or frame a lot of work – it is well worth the investment.) OR an X-acto Knife and Cutting Mat
  • Linen Gummed Hinging Tape – One small roll will last you a long time and it is reversible if you make a mistake or want to re-frame something later on.
  • Small T-Square  or a Ruler
  • Microfiber Rag – these are essential for cleaning frames because they leave no dust.
  • Scissors
  • Pencil and eraser
  • Scrap paper for making a mock-up
  • Optional: Drafting Tape  for initial positioning of artwork


Step 1:
Clean everything with your microfiber rag and some glass cleaner.  Clean your work area, clean your frame, take it apart and clean both the inside and the outside.  This may seem like overkill, but you’d be surprised at how dirty frames can be even when they are new.  This will keep little black specks of dust and errant cat hairs at bay. 

Framing Tutorial 03

Step 2: 
Make a template of your frame insert (or use the back of the paper that comes in your frame).  This will help you get accurate measurements for centering your artwork in your frame.

Framing Tutorial 04

Step 3:
Measure your artwork and center it on your template.  I like to have my artwork centered width-wise, and have a little bit more space on the bottom than on the top length-wise.   Make small marks showing where the corners are.

Framing Tutorial 06

Step 4:
Establish a ‘cut line’ that is about 1/3” down from the top of the print.  This is where we’ll cut a slit in the backing board to mount work invisibly

Framing Tutorial 07

Step 5:
Cut out mat board to use as your backing.  Use your mat cutter or your xacto knife and a ruler to produce a straight 90 degree cut.  If using your xacto knife, make sure to take your cuts slow – you’ll need multiple careful passes to cut through your mat board.  Be patient.

Framing Tutorial 09

Framing Tutorial 10

Framing Tutorial 011

Step 6:
Once your mat board is cut, lay your template over the mat board and transfer the ends of your cut line by pushing your pencil through your paper.  It should create a small indent that you can then use a ruler to connect.

Framing Tutorial 12

Framing Tutorial 13

Framing Tutorial 14


Framing Tutorial 15

Step 7:
Using your Mat Cutter or your Xacto knife, cut a slit along your cut line through to the back of your paper.  This cut should be the opposite directions that you usually cut mat bevels, and should be at a 45 degree angle.  If using an Xacto knife, it may take a bit of practice to get this technique down.

Framing Tutorial 16

Framing Tutorial 17

Framing Tutorial 18

Step 8:
Once your bevel is cut, take some pieces of Linen tape about 2” long  and cut them to be about 1/2” wide.  If you are hinging a larger piece, use 3” long tape and use the full 1” width. 

Framing Tutorial 19


Step 9:
Mount the tape in a small square to the back of the artwork.  If mounting a photograph, or something on really thin or translucent paper, the linen mounting tape might not work the best – you may want to try a self-adhesive archival tape.  Make sure you don’t add too much water to the tape – I like to put the water on, let it sit for a few seconds to absorb into the tape, and then adhere it to the back of the print.  Make sure you mount it lower than 1/3” from the top – I like to mount mine about 2/3” from the top so that I have a little vertical space to work with when adjusting my artwork.  Also be mindful not to mount the tape pieces wider than your slot in your mat board.

Framing Tutorial 21


Framing Tutorial 20


Framing Tutorial 22

Step 10:
Slide the tape through the slit in the mat board and adjust it until your print sits exactly where you want it.  I like to use some drafting tape on the back once I get it situated before I adhere it to the back of the mat board to double check that the print sits just right before adhering the gummed linen tape to the mat. 


Framing Tutorial 23


Framing Tutorial 24


Framing Tutorial 25


Framing Tutorial 26


Step 11:
Once you’ve double-checked your placement, adhere the linen tape to the mat board and take an additional piece to place over your slot.  This will keep it from bowing out or warping over time. 


Framing Tutorial 27


Framing Tutorial 28


Framing Tutorial 29



Step 12:
Place your artwork in your frame and enjoy! 
Framing Tutorial 30



The wonderful piece in this tutorial is a print by Michael McGovern - a grad school friend, and wonderful printmaker based in Portland - click on his name to check out his website and other work!


No comments:

Post a Comment